Product Introduction
Our Sleeve Type Blow-down Valve is engineered for throttling, pressure reducing and intermittent blowdown/discharge service, especially for high pressure drop, cavitation-prone operating conditions. Its unique sleeve sliding nozzle structure directs cavitation bubbles to the center of the flow stream, avoiding pitting and erosion damage to valve body and seat surfaces. It delivers linear flow control across the full stroke (10% stroke = 10% flow), unlike conventional valves limited to 20–80% controllable range. Double sealing (hard alloy + soft seal) provides Class V/VI zero-leakage performance; balance hole piston design reduces operating torque and enables stable operation under full differential pressure. Quick-detachable trim allows in-line seal and packing replacement without full valve removal. Available in multiple body materials and actuation options, it serves as a reliable, long-life solution for boiler blowdown, process vessel discharge, pressure reducing and high differential pressure applications where conventional valves suffer rapid cavitation erosion.
Product Features
1.Anti-Cavitation & Erosion Resistant Design: Specially sized sleeve nozzles direct cavitation bubbles to the center of the flow stream, avoiding collapse near metal surfaces and eliminating pitting erosion. STL (Stellite) hardfaced core/seat (HRC55+) and hardened sleeve further enhance wear resistance, extending service life in high pressure drop blowdown service.
2.Full-Stroke Linear Flow Control: Delivers proportional linear flow across the entire 0–100% stroke range - 10% stroke increase corresponds to 10% flow increase - enabling predictable, precise throttling and pressure reduction from near-closed to near-open, simplifying PID loop tuning for automated control.
3.Double Sealing Zero-Leakage Performance: Hard alloy primary seal provides wear resistance; soft secondary seal (PTFE/graphite/elastomer) compensates for surface imperfections, achieving Class V bubble-tight or Class VI zero leakage per ANSI/FCI 70-2 standards. Redundant sealing maintains performance even if soft seal is damaged.
4.Low Torque Balance Hole Piston: Disc balance holes equalize pressure across the disc, eliminating unbalanced fluid force for light, low-torque operation even under maximum differential pressure. This reduces actuator size requirements and enables feasible manual operation for larger sizes and high pressures.
5.Multiple Actuation & Quick-Detach Maintenance: Supports manual handwheel, pneumatic (1–4s customizable fast close) and electric (intelligent/explosion-proof) actuation. Quick-detachable trim design enables in-line replacement of sleeve, core and packing without removing the valve body from pipeline, minimizing downtime.
6.Wide Specification Range & Global Compliance: Size range DN20–DN400; pressure PN10–PN160; temperature -20~566℃. Materials include WCB, SS304/316/316L, F11/F22/F91 alloy steel and NACE MR0175 sour service options. Complies with API 6D, ANSI B16.31, MSS-SP-61, NACE, ATEX and ISO 9001 standards.
Working Principle
Sleeve Blow-down Valve: rotate handwheel/actuator, sleeve slides inner sleeve nozzles - flow changes, throttling. Closed: covers nozzles, blocked - double sealing (hard+soft) zero leak. Open: uncovers nozzles, linear flow (10% stroke = 10% flow) - full-stroke vs 20–80% limit. Cavitation to center - avoids erosion. Disc balance holes, piston - balanced, low torque. Core/seat STL hardfaced, sleeve hardened - wear/cavitation resistant. Quick-detach, online packing. DN20–400, PN10–160 / Class 150–2500, 935 PSIG, -20~566℃. WCB/SS304/316/F11/F22/F91/NACE. PTFE/graphite/hard alloy. Flange/thread/weld. Manual/pneumatic/electric, fast 1–4s. Class V/VI. API 6D/ASME/ANSI/MSS. ISO9001/CE/ATEX/NACE.
Application Scenarios
Boiler & Steam Systems: Used for continuous throttling, bottom blowdown (particle/sediment discharge) and surface blowdown in industrial boilers. Anti-cavitation design handles high-pressure boiler water flashing to steam; STL trim resists erosion from particulate-laden boiler water.
Petrochemical & Oil & Gas: Applied for process vessel blowdown, pressure relief and medium discharge in refineries and gas processing. NACE MR0175 compliant materials resist sulfide stress cracking in sour H₂S service; zero-leakage double sealing prevents hazardous emissions.
Power Generation: Deployed in thermal power plant steam boiler blowdown, water column drainage and gas turbine blowdown systems. Alloy steel grades and graphite seals withstand high-temperature steam up to 566℃; linear flow characteristic enables precise continuous blowdown control.
Water Treatment & Environmental: Used for filter backwash, sediment discharge, pressure reduction and sewage blowdown in municipal and industrial water treatment systems. Stainless steel body and corrosion-resistant seals handle water and mild corrosive wastewater; quick-detach design simplifies maintenance.
Metallurgy, Chemical & Pharmaceutical: Suitable for metallurgical process fluid blowdown, chemical acid/alkali solvent discharge and pharmaceutical clean steam/CIP drain. Broad material options including SS316L and FDA-compliant seals meet GMP and food safety requirements.
Quality Assurance
Every Sleeve Blow-down Valve: Material cert - WCB, SS304/316/316L, F11/F22/F91 alloy, NACE MR0175, MTR 3.1. Sleeve/core - stainless, hardened alloy, STL surfacing HRC55+, dye penetrant. Seal - PTFE/graphite/hard alloy dual, compression test, Class V/VI. Pressure - 100% shell 1.5×PN, seat 1.1×PN, air, zero leak; API 598/ANSI/MSS. Functional - torque, full stroke, linear flow (10%=10%), nozzle check, actuator cycle, pneumatic fast 1–4s. Connection - flange ASME/DIN, thread NPT/BSP gauged, weld SW/BW. Surface - paint corrosion (salt spray), SS pickled. Marking - permanent material/size/pressure/flow/standard/serial. ISO9001, CE, ATEX, NACE. Batch traceable. Warranty.
FAQ
Q1: How does the sleeve nozzle design solve cavitation and erosion?
A: Specially sized nozzles direct cavitation bubbles to the center of the flow stream, so bubble collapse occurs within the fluid rather than against metal surfaces, eliminating pitting erosion. STL hardfaced trim and hardened sleeve further enhance wear resistance for long service life in high pressure drop blowdown service.
Q2: What sizes, pressures, temperatures and materials are available?
A: Size range DN20–DN400; pressure PN10–PN160 (Class 150–2500), max working pressure 935 PSIG; temperature -20~566℃. Body materials: WCB carbon steel, SS304/316/316L stainless steel, F11/F22/F91 Cr-Mo alloy steel, NACE MR0175 sour service option. Seals: PTFE, graphite, hard alloy in dual hard+soft configuration.
Q3: What is the linear flow characteristic, and how is it better than conventional valves?
A: Linear flow means 10% stroke increase = 10% flow increase across the full 0–100% stroke range, unlike conventional valves only controllable in the 20–80% range. It enables predictable precise throttling, usable control at very low openings, and simplified PID tuning for automated control loops.
Q4: What actuation options and sealing classes are available?
A: Actuation: manual handwheel, pneumatic (1–4s customizable fast close), electric (intelligent/explosion-proof). Sealing class: Class V (bubble-tight gas) or Class VI (zero leakage soft-seat) per ANSI/FCI 70-2, with Class VI optional for critical applications.
Q5: What standards, warranty and lead time apply?
A: Standards: API 6D, ANSI B16.31, MSS-SP-61, NACE, ATEX, ISO 9001. Warranty: 18 months from shipment or 12 months from installation. Lead time: 20–35 days standard, 35–60 days for custom configurations. MOQ is 1 piece; sample orders accepted.
Hot Tags: Sleeve Type Blow-down Valve | Anti-Cavitation Linear Flow Industrial Throttling Blowdown Valve, China Sleeve Type Blow-down Valve | Anti-Cavitation Linear Flow Industrial Throttling Blowdown Valve manufacturers, suppliers, factory, factory high pressure globe valve, Suppliers ball valve globe valve, crane bronze globe valve, globe stop valve, 1 2 brass globe valve, globe type silent check valve
| Item | Specification |
|---|---|
| Product Name | Sleeve Type Blow-down Valve |
| Valve Type | Sleeve sliding nozzle blow-down valve; anti-cavitation; linear flow; double sealing |
| Nominal Diameter | DN20 – DN400 (3/4" – 16") |
| Nominal Pressure | PN10 – PN160 (Class 150 – Class 2500); max 935 PSIG |
| Operating Temperature | -20℃ ~ 566℃ (material dependent) |
| Body Material | WCB, SS304/316/316L, F11/F22/F91 Alloy Steel; NACE MR0175 optional |
| Trim Material | STL (Stellite) hardfaced core/seat, HRC55+; hardened sleeve |
| Seal Material | PTFE, Graphite, Hard Alloy; dual hard+soft seal; Class V/VI |
| Drive Mode | Manual handwheel, Pneumatic (1–4s fast close), Electric (intelligent/explosion-proof) |
| End Connection | Flanged, Threaded (NPT/BSP), Welded (socket/butt weld) |
| Design Standard | API 6D, ANSI B16.31, MSS-SP-61, ISO 9001 |
| Warranty | 18 months from shipment |







