Proppant-Type Temporary Blocking Agent | Degradable Fracturing Plug | 40-150°C | Factory

Proppant-Type Temporary Blocking Agent | Degradable Fracturing Plug | 40-150°C | Factory
Details:
The Proppant-Type Temporary Blocking Agent is a degradable polymer particulate engineered for temporary zonal isolation and diversion during hydraulic fracturing operations. Unlike conventional proppants (ceramic/sand) that remain permanently in fractures, this blocking agent is fully soluble — forming a dense temporary plugging layer on proppant beds or mixing with proppant to seal perforations and divert fracturing fluid to under-stimulated zones, then completely dissolving in wellbore fluids after stimulation. Available in four grades (L40/L70/H90/ST120) covering 20°C to 150°C, with compressive strength up to 50MPa and customizable grain size and dissolution rate. A unique feature of certain grades is organic acid generation during degradation — providing in-situ acidizing to remove formation damage and gel-breaking action simultaneously. Widely used in refracturing, vertical well stratified fracturing, horizontal well multi-stage fracturing, and complex well stimulation — this intervention-free blocking agent dissolves completely into water and CO₂, leaving no residue and causing no formation damage.
Send Inquiry
Add To Inquiry
Download
Description
Technical Parameters
Product Introduction

 

The Proppant-Type Temporary Blocking Agent is a specialized soluble and degradable polymer particulate designed for temporary plugging and diversion in hydraulic fracturing operations. It is important to distinguish this product from conventional proppants: while traditional proppants (ceramic, sand, resin-coated sand) are designed to permanently prop open fractures, our temporary blocking agent is engineered to temporarily seal perforations and proppant beds, then fully dissolve after the fracturing operation is complete.

We provide a full range of temporary blocking agents across four temperature grades: low temperature (L40, 20–60°C), medium temperature (L70, 60–90°C), high temperature (H90, 90–120°C), and ultra-high temperature (ST120, 120–150°C). The agent is manufactured from dissolvable and degradable polymer materials, and can form a dense blocking layer on the proppant bed or be mixed with proppant under pressure to achieve effective temporary zonal isolation. Customization is available for dissolution rate and grain size to match specific well conditions and operational requirements.

A unique advantage of certain grades is that the degradation process generates organic acids, which provide in-situ acidizing to remove near-wellbore formation damage and simultaneously break fracturing fluid gel. The blocking agent dissolves completely in water or degrades into water and CO₂ - safe, reliable, and non-damaging to the formation. To date, we have developed more than 40 formulations of temporary blocking agents for customers, which have been widely applied in major oilfields with proven stimulation effects.

 

Product Features

 

1. Fully Degradable, Zero Formation Damage

The blocking agent is manufactured from soluble polymer materials that dissolve completely in wellbore fluids after stimulation - degrading into water and CO₂ with no solid residue, no formation plugging, and no requirement for post-frac cleanout or milling operations.

2. Four Temperature Grades, Wide Adaptability

Available in four grades - L40 (20–60°C, flexible), L70 (60–90°C, flexible), H90 (90–120°C, rigid), and ST120 (120–150°C, rigid) - covering low, medium, high, and ultra-high temperature wells. Each grade is formulated for optimal plugging performance and controlled degradation at its target temperature range.

3. Dual Plugging Mechanism

The agent can function in two modes: (a) forming a dense low-permeability layer on top of the proppant bed to block fluid entry, or (b) mixing directly with proppant to create a temporary permeable barrier. This flexibility allows adaptation to different wellbore conditions and diversion strategies.

4. In-Situ Acid Generation & Gel Breaking (Selected Grades)

Certain formulations generate organic acids during the degradation process, providing dual-action benefits: the acid dissolves near-wellbore formation damage (scale, mud cake, polymer residue) and breaks fracturing fluid gel - improving post-frac conductivity and production recovery without additional acidizing treatments.

5. Customizable Grain Size & Dissolution Rate

Standard grain sizes range from fine powder to granular particles, with custom sizes available. Dissolution rate can be formulated from rapid (hours) to extended (days) based on downhole temperature, fluid chemistry, and required plugging duration.

6. High Compressive Strength

L40/L70 grades: ≥40MPa compressive strength. H90/ST120 grades: ≥50MPa compressive strength. Maintains structural integrity and plugging performance during high-pressure fracturing operations.

 

Working Principle

 

The Proppant-Type Temporary Blocking Agent operates in four stages:

1. Deployment Stage

The blocking agent (in granular or powder form) is mixed with fracturing fluid or carrier fluid and pumped downhole using standard pumping equipment. No specialized tools are required. The particles travel through the wellbore suspended in the fluid stream.

2. Temporary Plugging Stage

Upon reaching the target zone, the blocking agent particles accumulate either on the proppant bed (forming a dense low-permeability layer) or within the proppant pack (mixed plugging). Under differential pressure, the particles compact and create an effective temporary seal, blocking fluid entry into already-stimulated perforations or zones. This forces the fracturing fluid to divert toward untreated intervals.

3. Degradation Stage

After fracturing operations are complete, the polymer blocking agent begins to dissolve in the wellbore fluid at downhole temperature. The dissolution rate is controlled by the grade formulation and temperature. For acid-generating grades, organic acids are released during degradation, providing in-situ acidizing and gel-breaking action.

4. Flowback Stage

Within the specified dissolution time, the entire blocking agent dissolves completely into water, CO₂, and non-toxic soluble byproducts. These are circulated out during well flowback, restoring full formation conductivity and wellbore access with no residual plugging material - eliminating the need for coiled tubing cleanout or milling.

 

Quality Assurance

 

All Proppant-Type Temporary Blocking Agents are manufactured and tested under strict quality control:

• Raw material inspection - polymer composition verification, molecular weight testing, and solubility calibration per batch

• Grain size analysis - sieve analysis and particle size distribution measurement per ISO 14688

• Density measurement - bulk density and specific gravity verification per grade

• Compressive strength testing - uniaxial compressive strength test at rated pressure (40MPa or 50MPa)

• Degradation testing - dissolution time verification in standardized brine at specified temperature, with complete dissolution confirmed

• Acid generation testing - for acid-generating grades, pH measurement and acid yield verification during degradation

• Packaging inspection - sealed moisture-proof packaging (bags or drums) with desiccant, labeled with grade, grain size, batch number, and manufacture date

We provide:

• 12-month product quality warranty from date of shipment

• Custom formulation development for specific well conditions

• Technical support for dosage calculation, mixing procedures, and degradation time matching

• Each shipment includes material test report (MTR), degradation test certificate, and product data sheet (PDS)

• Third-party inspection (BV/SGS) available on request

 

Application Scenarios

 

• Oil Well Refracturing (Re-Frac)

The primary application - temporary plugging of existing perforations and propped fractures to divert refracturing fluid into virgin reservoir rock, bypassing near-wellbore damage and accessing unstimulated zones for improved production recovery.

• Vertical Well Stratified Fracturing

Used for temporary zonal isolation between layers in vertical wells, enabling selective fracturing of multiple zones in a single trip without mechanical packers or bridge plugs.

• Horizontal Well Multi-Stage Fracturing

Deployed for temporary diversion between stages in horizontal well plug-and-perf completions, particularly where rapid, intervention-free stage isolation is required to minimize rig time and operational cost.

• Complex Well Reconstruction

Suitable for complex wellbore configurations (deviated wells, multilateral wells, old wells with casing damage) where mechanical isolation tools may be difficult to deploy or retrieve.

• Temporary Formation Damage Removal

For acid-generating grades - the in-situ organic acid production during degradation provides incidental acidizing to remove scale, mud cake, and polymer damage near the wellbore, improving post-frac conductivity.

• Proppant Flowback Control

Can be used as a temporary flowback control agent to prevent early proppant flowback during initial clean-up, then dissolves to allow normal production.

 

FAQ

 

Q: Is this a conventional proppant or a temporary blocking agent?

A: This is a temporary blocking agent, not a conventional proppant. While it is particulate in form (similar to proppant) and can be mixed with proppant, it is designed to dissolve completely after fracturing. Conventional proppants (ceramic/sand) remain permanently in the fracture to prop it open. We call it "proppant-type" because of its particulate form and compatibility with proppant handling equipment.

 

Q: How is the blocking agent different from a soluble bridge plug?

A: A soluble bridge plug is a solid mechanical tool that is set at a specific depth to isolate an entire zone. The blocking agent is a particulate material that is pumped and accumulates on proppant beds or in perforations to create a temporary seal. Bridge plugs provide full-bore isolation; blocking agents provide selective, distributed plugging for diversion. Both are fully degradable.

 

Q: How long does the blocking agent take to dissolve?

A: Dissolution time depends on the grade and downhole temperature. Standard grades range from several hours to several days. Custom dissolution rates can be formulated. L40 and H90 grades are designed for rapid dissolution (≤24h), while L70 and ST120 offer extended plugging (24–72h+). ⚠️ Exact times to be confirmed by engineering.

 

Q: What grain sizes are available?

A: We offer a range from fine powder to coarse granular particles. Standard mesh sizes include 20/40, 30/50, 40/70, and 100/200, with custom sizes available. The optimal size depends on perforation diameter and target plugging mechanism.

 

Q: How is the blocking agent deployed?

A: It is mixed with fracturing fluid or carrier fluid at the surface and pumped downhole using standard pumping equipment - no specialized tools required. It can be batch-mixed or continuously metered into the fluid stream. Dosage depends on the number of perforations, perforation size, and desired plugging thickness.

 

Q: How much blocking agent is needed per job?

A: Dosage depends on the target zone parameters - number of perforations, perforation diameter, wellbore diameter, and desired plugging layer thickness. Our technical team can provide dosage calculations based on your well data. Typical dosages range from 100kg to 2,000kg per stage, depending on application.

 

Q: Is the acid-generating feature available in all grades?

A: No, acid generation is available in selected formulations. Please specify if you require combined plugging + acidizing + gel-breaking functionality, and we will recommend the appropriate grade or develop a custom formulation.

 

Q: Is the blocking agent compatible with all fracturing fluids?

A: It is compatible with most water-based fracturing fluids, linear gels, and crosslinked fluids. Compatibility with specific additives (crosslinkers, breakers, surfactants) should be verified prior to use. Our technical team can provide compatibility testing.

 

Q: What is the MOQ and delivery time?

A: MOQ is 500kg for standard products. Delivery time is 7–15 working days for standard grades/sizes and 15–25 working days for customized formulations. We ship from Shanghai or Ningbo port in 25kg bags, 500kg bulk bags, or 200L drums.

 

Q: How should the blocking agent be stored?

A: Store in original sealed packaging in a dry, cool environment (below 25°C, relative humidity <60%), away from direct sunlight, moisture, and heat sources. Shelf life is 12 months from manufacture when stored under recommended conditions.

 

Hot Tags: Proppant-Type Temporary Blocking Agent | Degradable Fracturing Plug | 40-150°C | Factory, China Proppant-Type Temporary Blocking Agent | Degradable Fracturing Plug | 40-150°C | Factory manufacturers, suppliers, factory, Knot, meshes for oilfield tools, conductors for oilfield tools, demulsifiers for oilfield tubing accessories, anti wear agents for oilfield tool accessories, emulsifiers for oilfield tubing accessories

Number Colour Material density Bearing strength Texture of timber Temperature of use
L40 Pale yellow 1.1-1.25 g/cm3 ≥40MPa Flexibility 20-60℃
L70 Yellow 1.0-1.25 g/cm3 ≥40MPa Flexibility 60-90℃
H90 Gray 1.5-1.6g/cm3 ≥50MPa Rigidity 90-120℃
ST120 White 1.2-1.4g/cm3 ≥50MPa Rigidity 120-150℃
Send Inquiry