Feb 27, 2025

Introduction to shale gas extraction

Leave a message

In terms of shale gas completion:

 

The Barnett Shale is the first shale gas formation to achieve successful development in the United States and is also the highest-yielding shale gas field in the United States at present, becoming a global model. In the early stage, straight wells were used for development with poor results. Around 2000, it shifted to horizontal well development, and the production increased by 3 - 5 times. Currently, new wells in the United States almost all use horizontal wells. The depth is usually between 1200 and 2500 meters, and long curvature radius is used for steering to facilitate later measures and transformation. The horizontal section length is between 600 and 1500 meters. The latest horizontal section length exceeds 3000 meters. Most of the horizontal section ends are slightly higher than the heel by 15 - 45 meters, which is conducive to the return of fracturing and the flow of produced water to the lowest heel after production.

 

The horizontal well completion method has experienced a transition from casing completion to open-hole completion. In the early stage, 114.3 millimeters or 139.7 millimeters casing was used for completion, and drillable bridge plugs were used for multi-stage fracturing. In 2012, foreign countries were more inclined to use open-hole horizontal well multi-stage fracturing for completion and production. The number of fracturing stages has gradually increased to more than 20. For example, the Barnett shale gas reservoir has tried many completion methods, including casing + non-cementing + perforating + general fracturing, casing + cementing + perforating + restricted flow fracturing, casing + cementing + multi-stage fracturing, open-hole + liner + multi-stage fracturing, etc. Foreign comparisons show that the production effect of Barnett shale open-hole wells is significantly better than that of cemented wells.

 

In terms of shale gas hydraulic fracturing:

Shale belongs to an ultra-low permeability reservoir, and the permeability is mostly between 0.001 and 0.01 millidarcy. It must be fractured before it can be put into production. The single-well cost of shale gas fracturing in the United States is more than 5 million US dollars. Large-scale hydraulic fracturing is often used. Usually, 45 - 450 cubic meters of proppant is added, and the fracturing fluid is usually more than 10000 cubic meters. In 2000, large-scale water fracturing (also known as drag reduction water fracturing) was started. It has lower cost and better stimulation effect and has become the standard practice of fracturing operations. In the drag reduction water composition, clear water accounts for the vast majority. The most commonly used drag reducer is partially hydrolyzed acrylamide. Industrial drag reducer products have a very high molecular weight and can generate diversion fractures as long as cross-linked fluid or foam fluid at a lower cost. Drag reduction fracturing fluid usually uses small-diameter (40/70 mesh) proppant. For shale formations with developed natural fractures, smaller particle size (100 mesh) proppant needs to be considered. Although a large part of the generated fractures are not supported, due to the brittleness of shale, rock stratum slippage, and proppant bridge plugging/embedding effect, the fracture system will still provide higher "unsupported" fracture conductivity. ○ Usually, shale gas reservoirs are very thick and the length of horizontal sections is gradually increasing. Hydraulic fracturing construction will be implemented in multiple stages on the horizontal section. Each pumping is carried out for a shale gas reservoir layer. There is a separation between every two sections. The fracturing fluid in each layer section will also be divided into multiple plugs during pumping to form a more complex fracture network in the formation. After the ground equipment is pressure tested, "rock acid" is pumped in first to clean the near-well pollution. Then, the "drag reduction water" plug is injected. After that, a large amount of drag reduction water and low-concentration fine sand are injected. When the sand addition is about to end, drag reduction water and coarse sand are injected to maintain the opening of near-well fractures and obtain high conductivity near the well. Finally, drag reduction water is used for well washing and return to remove sand in the equipment and wellbore. ○ In order to improve operation efficiency and reduce costs, foreign countries have proposed the "well factory" concept. The well site or platform is regarded as a joint operation "factory" to complete the drilling, completion, and production of multiple wells. It has been realized that 16 horizontal wells and a total of 400 multi-stage fracturing completions have been completed on a well site. This makes the underground generated fracture network more complex, and the production effect is 75% - 130% higher than that of single-well fracturing. During fracturing, micro-seismic imaging and digital simulators can also be used to monitor the fracture characteristics in each stage of the shale reservoir and observe the growth track of fractures to evaluate the height, length, and orientation of fractures. During construction, operators should pay special attention to the vertical growth of fractures to ensure that hydraulic fractures do not penetrate the shale reservoir and extend to adjacent water layers.

 

Latest technologies:

In recent years, with the continuous progress of technology, some new shale gas exploitation technologies have emerged. For example, smart completion technology. By installing sensors and control systems in the wellbore, the production process can be monitored and controlled in real time to optimize production efficiency and output. There is also the application of nanotechnology in shale gas exploitation. Nanomaterials are used to improve the performance of fracturing fluid and improve the conductivity and stability of fractures. In addition, 3D printing technology has also begun to be applied in the manufacture of shale gas downhole tools to improve the accuracy and reliability of tools and reduce costs.

Send Inquiry