Model A,B & C Float Collar Float Shoe

Float collar and float shoe is a kind of down hole cementing tool which is widely used for Oil and gas drilling cementing operation. it is just like a kind of check valve, the cementing drilling fluid and slurry can only pumped from top end to bottom end . Float collars and float shoes are usually used together connect with one casing sting, there are some casing pipe between float collar and float shoe. The float shoe is always at the down most of the casing.

Typically, float collar a component installed near the bottom of the casing string on which cement plugs land during the primary cementing operation. it typically consists of a short length of casing fitted with a check valve. This device may be a flapper-valve type. a spring-loaded by valve or other type. The check-valve assembly fixed within the float collar prevents flow back of the cement slurry when pumping is stopped. With our float collar, the cement slurry placed in the annulus could U-tube, or reverse flow back into the casing. The greater density of cement slurry than the displacement mud inside the casing causes the U-tube effect.

Float shoe is a rounded profile component attached to the down hole end of a casing string. An integral check valve in the float shoe prevents reverse flow, or U-tubing, of cement slurry from the annulus into the casing or flow of well-bore fluids into the casing sting as it is run. The float shoe also guides the casing toward the center of the hole to minimize hitting rock ledges or washouts as the casing is run into the well bore. The float shoe reduces hook weight. With controlled or partial flip as the string is run, the casing sting can be floated into position, avoiding the need for the ring to carry the entire weight of the casing string. The outer portions of the float shoe are made of steel and general match the casing size and threads, though not necessary the casing grade. The inside (including the taper) is usually made of cement or thermoplastic, since this material must be drilled out if the well is to be deepened beyond the casing point.

Float collar and float shoe are all belong to floating equipment for drilling cementing application. Floating equipment is generally used in the lower section of the well to help reduce strain on the derrick while guiding casing past ledges and slough zones in the hole provide a landing point for bottom and top cementing plugs (pumped ahead of and behind the slurry as par of cementing operations) and also can provide a back pressure valve to prevent cement from flowing back into the inner diameter of the casing after the cement has turned the corner into the annulus and the to plug has been pumped.

Usually the float shoe contains a back pressure that prevents fluids from is lowered into the hole and prevents cement from towing pack into the placement, while enabling circulation down through the casing. Float collars are placed one the bottom plug pumped ahead of the cement and to the three points above the guide shoe or float Shoe top plug behind the full volume of slurry. Once seated, the top plug shuts off fluid flow and prevents over-displacement of the cement. The space between the float shoe and the float collar provides a containment area to entrap the likely-contaminated fluids from the wiping action of the top cementing plug, securing the contaminated fluid away from the shoe where a strong cement bond is of primary importance. Float collars include a back pressure valve and serve basically the same function as the float shoe.

Our Thankful Material cement float collar and float shoe are designed as per APl standards and improved from haliburton and schlumberger. Thankful Material is always working on total solution for float collars and float shoes. Our current product line include PDC drill-able cement float collar float shoe, non-drillable float collar float shoe, non-rotating float collar float shoe, stab-in float collar float shoe. PDC drillable auto fill cementing float collar and shoe, aluminum alloy float collar and shoe etc. All kinds of float collar and shoe include single valve and double valve style as option. All Thankful cementing float equipment float collars float shoes can be customizable according to client's requirement.

• Sized range from 4-1/2" to 20".
• High-strength metal can withstand excessive hydrostatic pressures exerted by cement columns to prevent formation damage and thereby significantly reduce costs and non productive time. Flexible, overlapping metal fins aid the basket in forming a bridge in the annulus to prevent cement from falling.
• Aluminium alloy material used for working pressure 35 Mpa, pipe size s5 inch Cement material used for working pressure s 35 Mpa, pipe size = 5.5 inch Non-rotating style is better than conventional style.
• Stub in style is can be used for pipe size more than 13-3/8 Inch.
• Stub in style no need any cement plug to displace mud during

Hot Tags: model a,b & c float collar float shoe, China model a,b & c float collar float shoe manufacturers, suppliers, factory, Titanium Pie Cuts, Retrievable Packer 2, Titanium Collars, Retrievable Packer 1, Wireline Setting Tools, Hydro Mechanical Set Bridge Plug